• 易迪拓培训,专注于微波、射频、天线设计工程师的培养

处理器接口

录入:edatop.com    点击:
  • 概述

  • 程序编码


概述

这个样本程序通过处理器I/O端口与外部仪器进行通信。

这个程序将5(位2和位0设置为低,其他位设置为高)输出到处理器I/O端口的端口A,然后等待直到端口C的位3设置为低。

参见该程序的输入/输出数据。

程序编码

Excel VBA

Sub Handler_Click()

    Dim defrm As Long           'Session to Default Resource Manager.

    Dim vi As Long              'Session to instrument.

    Dim Out_Data As Integer     'Decimal value.

    Dim In_Data As Long

    Dim Bit_stat As Integer

    Dim Flag_bit As Integer

    Dim Out_Data_Bin As String

    Dim Ret As Long             'Return value.

    Dim i As Long

    Dim X As Long

    Const TimeOutTime = 40000    'timeout time.

    Out_Data_Bin = "00000101"      'Store the output data on the port A (binaly).

    Flag_bit = 3                             'Bit location (bit 3).

    

    Call viOpenDefaultRM(defrm)    'Initializes the VISA system.

    Call viOpen(defrm, "GPIB0::17::INSTR", 0, 0, vi)   'Opens the session to the specified instrument.

    Call viSetAttribute(vi, VI_ATTR_TMO_VALUE, TimeOutTime)   'The state of an attribute for the specified session.

    

    Call viVPrintf(vi, "*RST" & vbLf, 0)    'Presets the setting state of the ENA.

    Call viVPrintf(vi, "*CLS" & vbLf, 0)   'Clears the all status register.

    

    Call viVPrintf(vi, ":CONT:HAND:C:MODE INP" & vbLf, 0)     'Configures the port C to input port.

    Call viVPrintf(vi, ":CONT:HAND:IND:STAT ON" & vbLf, 0)    'Line enable /INDEX signal.

    Call viVPrintf(vi, ":CONT:HAND:RTR:STAT ON" & vbLf, 0)   'Line enable /READY FOR TRIGGER signal.

    

    For i = 1 To Len(Out_Data_Bin)    'Convert Out_Dara_Bin to a decimal value.

        If Mid(Out_Data_Bin, Len(Out_Data_Bin) - i + 1, 1) = "1" Then

            X = 2 ^ (i - 1)

            Ret = Ret + X

        End If

    Next i

    Out_Data = Ret       'Sets the decimal value.

    Call viVPrintf(vi, ":CONT:HAND:A " & Ret & vbLf, 0)    'Sets to the port A.

    

    Call viVPrintf(vi, ":CONT:HAND:C?" & vbLf, 0)   'Outputs data to output port C.

    Call viVScanf(vi, "%t", In_Data)    'Reads data from the port C.

    

    Call ErrorCheck(vi)      'Checking the error.

    

    Call viClose(vi)           'Closes the resource manager session.

    Call viClose(defrm)     'Breaks the communication and terminates the VISA system.

    

    End                    

End Sub

Sub ErrorCheck(vi As Long)

    Dim err As String * 50, ErrNo As Variant, Response

    

    Call viVQueryf(vi, ":SYST:ERR?" & vbLf, "%t", err)    'Reads error message.

    ErrNo = Split(err, ",")  'Gets the error code.

    

    If Val(ErrNo(0)) <> 0 Then

        Response = MsgBox(CStr(ErrNo(1)), vbOKOnly)  'Display the message box.

    End If

End Sub

HT Basic (handler.htb)

10 INTEGER Out_data,In_data,Bit_stat

20 DIM Out_data_bin$[9]

30 !

40 ASSIGN @Agte507x TO 717

50 !

60 Out_data_bin$="00000101"

70 Flag_bit=3

80 !

90 OUTPUT @Agte507x;":CONT:HAND:C:MODE INP"

100 OUTPUT @Agte507x;":CONT:HAND:IND:STAT ON"

110 OUTPUT @Agte507x;":CONT:HAND:RTR:STAT ON"

120 !

130 Out_data=IVAL(Out_data_bin$,2)

140 OUTPUT @Agte507x;":CONT:HAND:A ";Out_data

150 !

160 REPEAT

170 OUTPUT @Agte507x;":CONT:HAND:C?"

180 ENTER @Agte507x;In_data

190 Bit_stat=BIT(In_data,Flag_bit)

200 UNTIL Bit_stat=1

210 END

矢量网络分析仪使用培训教程套装,让你快速掌握网分使用

上一篇:峰值搜索
下一篇:夹具仿真器

微波射频测量操作培训课程详情>>
射频和天线工程师培训课程详情>>

  网站地图